DYSON DC04 PROBLEM SOLVING

Its a question you will find the answer to here: How do i fit a drive belt to my yellow dyson 04, it is encased where the belt is supposed to be threaded through. Shame on Mr Dyson! I have a DC04 where the roller is not rotating. The only course of action is to replace the entire filter if your suction is good when the filter is removed. This was partly due to the brush roller end cap plastic drive dogs being extremely worn.

If you are a Dyson DC07 owner click here for a separate troubleshooting guide. The brush is clean and debris free. I used a volt meter and checked voltage at the plug where the brush attaches and got no reading. Unless you are quite experienced with this stuff, I would give that one to a local Dyson specialist to fix. I thought it may be an electrical connection problem but have tried to change the pressure at the connection points but this has no effect. This is the usual problem: Full size vacuums Upright corded vacuums engineered to clean across all floor types.

The tension between cd04 clutch and the beater bar is solid I needed the tool to get the brush off! Had a look at the DC24 recently and realised that the brush roller at the drive end and clutch were causing the roller to wobble about like a bandy knee.

It sound that your DC15 have an electric issue, may be electronics.

dyson dc04 problem solving

This was partly due to the brush roller end cap plastic drive dogs being extremely worn. Suzanne on September 19th, at 1: I cleaned the filter, cleaned the brush, checked all the connections for blockage, and I even just replaced the clutch.

  DISSERTATION BTS ESF

Welcome to Dyson

Check to see if the brush bar spins when the machine is reclined in the cleaning position! DC20 – Remove the cyclone and bin, open the lid at the top of the machine and wash the circular filter.

I have a DC14 where the brush probblem had stopped turning, the motor was spinning. Next use a a coin to open the blue screw next to the large wheel, open the solvinb hatch and remove the large cylinder filter. Next determine if it is from the base or the handle if you are still having problems, click one of the links below: DC15 – wash the filter above the bin in the cyclone top.

Had a look at the DC24 recently and realised that the brush roller at the drive end and clutch were causing the roller to wobble about like a bandy knee. There is suction from the bottom, but only limited pick up due to the brush bar not turning. The brush is clean and debris free. I dyosn a Dyson DC07 and the brush is not spinning when reclined.

The Brush Roll Won’t Turn – Dyson DC04, Dyson DC07 and Dyson DC14

Help I have owned for 10 years and want to give it one more shot before kicking it to the curb. If you can’t see daylight trust me it is still blocked even if a coathanger goes all the way through. But fitting it is not really an amateur job.

Your remedy of removing the roller end caps and removing approximately 18 years of muck,dust and hair from the metal posts has done the trick.

Dyson vacuum cleaner suction problems troubleshooting – not picking up

Bought a Dyson DC24, for its lightness and ease of use, in the early days of production. Angus Black on May 21st, at 6: Angus Black on April 21st, at 9: To clear the wand handle get a wire coat hanger straighten it out but keep a hook on the end to stop you losing it down the handle. Angus Black on January 24th, at And clutch stripping instructions are here: It worked Ok for six months or so until it began to sound like a very large and powerful tractor.

  SHARJAH INDIAN SCHOOL HOLIDAY HOMEWORK 2016-17

We don’t stop caring about our products once they’re yours.

dyson dc04 problem solving

This mainly occurs when the cage that holds the washable filter becomes blocked and cannot be cleaned resulting in loss of suction across the whole machine. Hassle-free replacement If we can’t repair proble machine, we’ll replace it while it’s under guarantee.

Unless you are quite experienced with this stuff, I would give that one to a local Dyson specialist to fix.

If you are testing it in the upright position then suction is diverted to the wand. DC02 two rectangular filters visible cc04 the cyclone top is opened.

Angus Black on May 24th, at 5: Explore the lightweight range of Dyson cordless vacuums. I have taken the roller out and checked for blockages on the roller and edges but as I say it is new, so it is hardly dirty.